Most hydronic callbacks trace back to the same thing: black sludge. Magnetite forms inside steel radiators, boilers and pipework as the system corrodes from the inside, and once it's circulating it wears pump seals, blocks narrow heat exchanger passages and quietly kills efficiency.
The usual fix, if there's any filtration fitted at all, is a basic in-line strainer. A strainer catches grit and swarf left over from the install, but it does nothing for the fine magnetic sludge that actually does the damage - that needs a magnet.
RBM makes six different magnetic filters, each built for a different spot in the system: a combined air-and-dirt-and-magnet unit, two standalone magnetic separators, two heat-pump-specific diverter filters, and a compact under-boiler unit. This post runs through where each one goes, using the 3/4in Mag-nus2 as the reference point.
What a Magnetic Filter Actually Does
Every RBM filter in this range uses the same core idea: an 11,000 gauss neodymium magnet sits inside a stainless steel AISI 304 cartridge, and the circuit's full flow passes through it. Ferrous particles - magnetite, rust and weld scale - stick to the cartridge instead of continuing around the loop.
Fit it in the return line, as close to the boiler or heat pump as the pipework allows. That's where the dirtiest water is heading, and it's the easiest point to service.
Six Units, Six Jobs
They're not interchangeable:
- Mag-nus2 (3548.05.00) - a straightforward 3/4in magnetic sludge remover for a general heating circuit. Kv 9.50 m³/h, 10 bar max operating pressure.
- Airterm Mag (2863.05.00) - the same magnetic separation plus a float-operated deaerator in one body, so it strips air as well as sludge. Kv 12.66 m³/h.
- SafeCleaner2 (2405.05.00 / 2405.06.00) - a nickel-plated brass diverter body in 3/4in or 1in, built to go in either horizontal or vertical pipework under a boiler or heat pump.
- MP1 (3699.06.00) - purpose-built for heat pump circuits, 1in, with an integrated shut-off and discharge cock so it can be cleaned without draining the system. Kv 17.3 m³/h.
- MP2 (3833.06.00) - also for heat pumps, with a brass diverter body for horizontal or vertical runs where MP1's fixed body doesn't suit the pipe layout.
- MG1 (3070.05.00) - a compact 3/4in unit with a swivel boiler connection and ball valve, for tight plant rooms where there's no room for a full diverter body.
Match the connection size to the pipe, not just to the boiler's output. The 3/4in units (Mag-nus2, Airterm Mag, MG1) suit a typical single-dwelling gas boiler circuit, while the 1in MP1 and MP2 suit the larger flow rates common on ducted or multi-zone heat pump systems. Running full flow through an undersized filter just adds pressure drop the pump has to work against, so check the Kv figure against your design flow rate before you order.
Heat Pump Circuits Need Their Own Filter
MP1 and MP2 aren't just rebadged versions of the Mag-nus2. Heat pump heat exchangers have much finer waterways than a gas boiler's, so they're far less tolerant of sludge and need a filter sized and rated for that duty. RBM rates both to 6 bar and 70°C, noticeably lower than the 10 bar / 110°C of the general-circuit units - that's the heat pump application showing up in the spec, not a cut-down product.
Pick MP1 where the pipe run suits its fixed body and integrated shut-off; pick MP2 where you need the diverter body's flexibility on orientation.
Clean It Without Draining the System
Every unit in this range is self-cleaning by design: open the drain ball cock or ball valve, and the trapped sludge flushes out through a hose-end connector while the magnet stays in place. None of the six need the circuit drained down to service.
That matters for a maintenance contract - a five-minute flush at the drain cock beats isolating and draining a filled heating circuit every time you visit.
Build Quality
Across the range: brass bodies (nickel-plated on the SafeCleaner2's diverter), AISI 304 stainless steel filtering cartridges, and elastomer hydraulic seals. The polymer cartridge-holder bodies used on the SafeCleaner2, MP1 and MG1 keep weight and cost down on units that don't need a full brass shell.
Pressure and temperature ratings vary unit to unit - check the individual listing before specifying, particularly for the lower-rated heat pump units.
Compliance: Not for Potable Water
RBM's listings are explicit that every unit in this range is designed for closed-circuit hydronic heating and cooling systems, and none of them is a WaterMark-listed potable water product. Don't fit one to a drinking water line. Install to the heating/HVAC standards that apply on your job and the boiler or heat pump manufacturer's instructions for the equipment it's protecting.
Wrap-Up
If magnetite's the problem, a magnetic filter in the return line is the fix - just match the unit to the circuit. The Mag-nus2 covers a standard heating loop; step up to the MP1 or MP2 on a heat pump, and look at the Airterm Mag if you want air removal built into the same fitting. See the full range, plus air vents and safety valves for the rest of the circuit, in our Hydronic Heating Accessories collection. For the air-removal side of the same circuit, see our guide to automatic air vents and deaerators.
Frequently Asked Questions
Where should a magnetic filter go in a hydronic circuit?
In the return line, as close to the boiler or heat pump as practical. That's where sludge concentrates before it reaches the heat exchanger, and it's the easiest point to access for servicing.
Can I use the same magnetic filter on a gas boiler and a heat pump circuit?
Not ideally. RBM rates the heat pump units (MP1, MP2) lower on pressure and temperature than the general-circuit units, reflecting the finer waterways and different operating conditions of a heat pump heat exchanger. Use the unit rated for the equipment it's protecting.
Do these filters need the system drained to clean them?
No. All six units are self-cleaning - open the drain ball cock or valve and flush the trapped sludge out through the hose connector while the magnet and cartridge stay in place.
Are these WaterMark certified for drinking water?
No. RBM's listings state these units are designed for closed-circuit hydronic heating and cooling systems and are not WaterMark-listed for potable water use.
